PDA

View Full Version : GPM Rear Gear Box/Motor Mount


RussF
2008.02.28, 11:53 AM
I did a lot of searching but couldnt find a clear answer to my questions.
I keep breaking the upper link mounts and the lower shock mounts. This part seems to have all that incorporated into one piece.

Will this part (MOL1013-B3) replace the two stock pieces for the rear end?

http://i272.photobucket.com/albums/jj171/Bash_N_Thrash/mol1013-b3.jpg

Second question:
Is there a length difference in the mounting points for rear gear box/motor mounts? I have a Hummer H1.

Third question:
Will the rest of the stock plastic pieces mount up?

Thanks in advance for any help.

575racer
2008.02.28, 12:41 PM
yeah, i have that part on my ol. i bougth the arm mount aswell and was quite annoyed when i found out i didnt need to :eek:

RussF
2008.02.28, 02:00 PM
So then I'm right, that the arm mount is not needed? And the gear box fits?

575racer
2008.02.28, 02:49 PM
all fits fine. the motor clip/heatsink takes some force to get on and off but you probably wont change the motor much. i managed to shake a link screw out the screw hole:eek:

james399
2008.02.29, 02:42 AM
check the forsale section, i have it on an overland i'm selling with close up shots of the chassis, so you can see it installed... hope that helps...

I did a lot of searching but couldnt find a clear answer to my questions.
I keep breaking the upper link mounts and the lower shock mounts. This part seems to have all that incorporated into one piece.

Will this part (MOL1013-B3) replace the two stock pieces for the rear end?

http://i272.photobucket.com/albums/jj171/Bash_N_Thrash/mol1013-b3.jpg

Second question:
Is there a length difference in the mounting points for rear gear box/motor mounts? I have a Hummer H1.

Third question:
Will the rest of the stock plastic pieces mount up?

Thanks in advance for any help.

RussF
2008.02.29, 12:59 PM
Thanks James. I must have looked at 100 pictues in two posts and I cant find the picture. Could you post it here or link it for me. Thanks.

briankstan
2008.02.29, 01:10 PM
here are the pictures

http://www.mini-zracer.com/forums/attachment.php?attachmentid=24159&d=1204096499

http://www.mini-zracer.com/forums/attachment.php?attachmentid=24158&d=1204096489

http://www.mini-zracer.com/forums/attachment.php?attachmentid=24153&d=1204096384

http://www.mini-zracer.com/forums/attachment.php?attachmentid=24155&d=1204096415

Jace1283
2008.02.29, 08:02 PM
i just bought one of those, great price....seems to good to be true, i'll let ya know how it turns out

update: got it and installed it, sweet piece, easy install

danny250r
2008.05.09, 09:26 PM
is there any motor mounts that allow the gear mesh to be adjusted

RussF
2008.05.12, 10:20 AM
If you mean for drilled cans... I have not seen one, but that would be a great idea and would be simple to do for someone. Just extend the pinion side of the mount out and slot it to accept drilled cans. Hmmmmm....

If you mean for this mount then yes, you adjust the mesh in the usual way with the plastic spacers.

simogoose
2008.06.04, 07:33 PM
Where can I buy it?
These hop-ups seems to be very rare!!

RussF
2008.06.05, 10:18 AM
Where can I buy it?
These hop-ups seems to be very rare!!

They are still available on E Bay. Item #170218508209. They are $10 higher now but still half of what the other sellers want.

simogoose
2008.06.06, 06:13 AM
Thans for info, but this ebayer doesn't send to Italy... :(