View Full Version : Rimz
Legolas
2002.07.13, 09:16 PM
Anyone willing to give me a f-1 rear right rim or sell cheap?
mini-z
2002.07.14, 12:44 AM
Legolas, we have the original plastic rims available - email us if you need a set.
Josheus
2002.07.14, 05:43 AM
ha ha i have the exact same breakage!
gargoyle7642
2002.07.14, 08:38 AM
Ditto on the breakage of the right rear. Hopefully the group buy of the squat f-1 rims will solve any future problems of that happening again!
Mondo
2002.07.14, 12:21 PM
And....
You are not alone
me too. nad my competition
Kev71h
2002.07.14, 10:28 PM
oh my gosh!!!! ME TOOOOOO~!!!!!!!
WHATs the chance of that??????? I think it is a normal breakage because at the local place where I race at...there is another guy that has done the same..
Kev
Did your wheel break at the hub ? I have broken two but I have made a aluminium spacer to fit between hub and rim to give wheel extra strength and I have had no problems since. see pic.
Yep same here right rear
sheared off all but one of the drive pins
Can't complain too much car has done a power of work.
Terry
Kev71h
2002.07.15, 10:29 AM
wow..check YOU out with the aluminum spacers!!! You must be a machinist or something. Good thinking on your part.
Legolas
2002.07.15, 10:57 AM
Would u sell ur spacerz?
shaft
2002.07.15, 03:04 PM
i bet you could go to a hardware store and find a small washer that would do the same thing.
I machined the spacers out of aluminium. The hole is a transition fit over the hub (neat fit), the outside diameter of the spacer is a press fit into the rim and the spacer is thick enough so it is flush with the end of the hub. A standard washer would not work as I have measured the rim and made these spacers to suit. I have been using the spacers for two months the rims have had some hard hits but I have had no problems. I was looking at buying alloy rims but they would cost me too much from overseas here in Australia. I was going to machine my own alloy rims but they would have looked very plain compared to F1 rims or after market rims so I thought of this spacer to strengthen standard rims. This is a much simpler fix and they look like brake discs when looking through the rim.
Legolas
2002.07.16, 05:02 AM
T_G can u tell me how much u would sell me a set for??
Legolas,
Sorry I am not selling any. I made some at work for myself when I had some spare time.
T_G
Karl.no
2002.07.16, 01:20 PM
... I approached this problem differently. A small piece of plastic and super-glue. Total weight addition: 0,5g.
Here's the illustrated instructions:
http://uk.geocities.com/sabildz4/Models/124Rc/124RpTyre.htm
For those wanting to review the whole webpage, click on my "www" button.
DEREK A.
2002.07.26, 02:52 PM
CAN ANYONE TELL ME WHERE I CAN GET SOME ALLOY STEERING KNUCKLES FOR MINI-Z F1? I CAN'T SEEM TO FIND ANY.
West.F1
2002.07.26, 03:26 PM
i'm interested in the alloy knuckle arms myself and also the tie rods (my two most replaced parts so far).
GPM who are based in hong kong makes them:
http://www.gpmracing.com.hk/catalogue/MINI%20FORMULA%20I.jpg
i've asked the Shop about special order but unfortunately GPM are slow to reply. In fact i've even emailed GPM direct and am waiting for a reply as well. What gives?
ive got the money. Now if i can just spend it, me and my mini would be better off :D
mini-z
2002.07.26, 05:56 PM
West.F1, we'll be emailing you today on this, we've got your prices at last. Anyone else who's looking for GPM parts, please email us for a quote. Thanks!
West.F1
2002.07.26, 07:23 PM
thanks for the heads up MiniZ. i'll keep a look out for the email.
Legolas
2002.07.26, 08:51 PM
hey mini z how much for the graphite wings?
West.F1
2002.07.27, 12:20 PM
what happened? :confused:
vBulletin® v3.8.3, Copyright ©2000-2024, Jelsoft Enterprises Ltd.