Mini-Z, Kyosho Mini-Z Racer, MR-03, MR-02, MA-010, Forums, News, Pictures, Parts, and Shop - Mini-ZRacer.com
Forums, Mini-Z, MiniZ, Kyosho Mini-Z, Kyosho MiniZ, Kyosho Mini-Z Racer
Mini-Z Hop-Ups, Mini-Z Parts, MiniZ Hop-Ups, MiniZ Parts, Kyosho Mini-Z Hop-Ups, Kyosho Mini-Z Parts, Kyosho MiniZ Hop-Ups, Kyosho MiniZ Parts, Kyosho Mini-Z Racer Hop-Ups, Racer Kyosho Mini-Z Parts

Go Back   Mini-ZRacer.com Forums > Search Forums

Showing results 1 to 25 of 500
Search took 0.03 seconds.
Search: Posts Made By: LED
Forum: Motor Tech 2015.12.22, 03:04 PM
Replies: 11
Views: 2,186
Posted By LED
Gongrats! Nice work

Gongrats! Nice work
Forum: PN Racing 2015.10.15, 07:28 AM
Replies: 2
Views: 877
Posted By LED
What do you mean with center to center? I can...

What do you mean with center to center?
I can measure the mounting holes and length of the shocks if you like. But the center of the shocks will differ with the setup. The angle of the shocks, etc.....
Forum: LeViteZer 2015.10.13, 08:23 AM
Replies: 1
Views: 1,837
Posted By LED
additional magnets

Hi guys

My question is about the additional magnets.
Why is there only 1 large magnet, 3 mediums and 5 (I think can't tell from the picture) small magnets?
I would expect them to be even...
Forum: Beginner Questions 2015.06.20, 03:43 AM
Replies: 3
Views: 529
Posted By LED
Did you try the standard troubleshooting things...

Did you try the standard troubleshooting things first,
Replaced the motor, or just measure if you get any voltage while hitting the throttle. Maybe some water also got into the motor and it rusted...
Forum: Parts and Hop-ups 2015.06.10, 10:03 AM
Replies: 4
Views: 1,082
Posted By LED
You can get the atomic top cover I think, but...

You can get the atomic top cover I think, but that will costs you money.
It will be probably be cheaper to buy 3 standard covers to replace the one you cut.
Just try it, you cant do anything wrong...
Forum: Parts and Hop-ups 2015.06.09, 11:24 PM
Replies: 4
Views: 1,082
Posted By LED
It's the same cover as a standard MR03. You...

It's the same cover as a standard MR03.
You have to cut them off :-)
Should be in the manual.
Forum: Parts and Hop-ups 2015.05.31, 03:33 PM
Replies: 2
Views: 1,131
Posted By LED
PN double a-arm vs Levitezer vs standard alu

Hi

I'm thinking about getting back into mod racing.
This is my situation. I used to race mod with an MR02 with double a-arm. So I know how it works and hwo to set it up for my needs.
I will be...
Forum: Motor Tech 2015.05.15, 12:55 AM
Replies: 13
Views: 3,992
Posted By LED
You can try shifting your centre point and then...

You can try shifting your centre point and then adjust your end point. The problem then could be that it will be more difficult to get into reverse.
Forum: Kyosho 2015.05.09, 10:01 AM
Replies: 42
Views: 3,392
Posted By LED
If you look at the botom of the buggy, next to...

If you look at the botom of the buggy, next to the switch the positive. And yes on the other side of the buggy the negative one.
You shpould have 4.8V minimal without even turning on the switch.
Forum: Kyosho 2015.05.09, 02:59 AM
Replies: 42
Views: 3,392
Posted By LED
Is your steering working? If not then the...

Is your steering working? If not then the problems is not there. Those are the motor connections. I assume you are simply not getting any power to the print of the buggy. So ignore those for the...
Forum: Kyosho 2015.05.07, 04:30 PM
Replies: 42
Views: 3,392
Posted By LED
Push the battery's hard into the positive...

Push the battery's hard into the positive direction with a screwdriver or something. Sometimes they are a tight fit and don't touch the positive side.
If you want to double check and have...
Forum: Motor Tech 2015.05.05, 04:31 PM
Replies: 12
Views: 1,397
Posted By LED
Well I can confirm one thing 100%, it has nothing...

Well I can confirm one thing 100%, it has nothing to do with the car because I have been testing today with only a 4 cell battery pack directly to the motor and I have that same issue with all my...
Forum: Motor Tech 2015.05.05, 10:25 AM
Replies: 12
Views: 1,397
Posted By LED
Realy? I searched the forum but didnt find...

Realy? I searched the forum but didnt find anything related. I also have been using the forum for 6 years now (with a pause of about 1,5 years) but I cant recall such a discussion.

I'll look again...
Forum: Motor Tech 2015.05.04, 04:06 PM
Replies: 12
Views: 1,397
Posted By LED
The motor tester didn't happen, something came up...

The motor tester didn't happen, something came up so I cant confirm it realy is a motor issue yet.

Why would they make the slower in the forward direction? Doesnt make sense to me :p
Thx for the...
Forum: Motor Tech 2015.05.04, 12:53 PM
Replies: 12
Views: 1,397
Posted By LED
Stock motor faster in reverse.

Hi guys, need some help understanding this.
I have 5 or 6 stock motors, most used, 2 only broken in.
they all are faster in reverse then in forward direction. Some up to 3500 RPM, measured with the...
Forum: Beginner Questions 2015.04.05, 02:45 PM
Replies: 13
Views: 1,334
Posted By LED
I simply replaced it with an electric wire the...

I simply replaced it with an electric wire the same length (important!!), and a little bit thicker. It was flexible copper stranded wire. No problem what so ever with range or reception. It's basicly...
Forum: Beginner Questions 2015.04.04, 06:14 AM
Replies: 9
Views: 955
Posted By LED
Nr 1 mistake that beginners make with stock diffs...

Nr 1 mistake that beginners make with stock diffs is overtightning the nuts on the left hand side.
When you pick up the car and spin one wheel with your fingers, the other wheel should smoothly and...
Forum: Parts and Hop-ups 2015.03.31, 10:19 AM
Replies: 36
Views: 2,757
Posted By LED
Well If you aver try this again, I suggest...

Well If you aver try this again, I suggest feeding 4 cells to the board and make a 6 cell connection right on the FET feading lines. After all, a FET is intented to switch on a higher power then the...
Forum: Motor Tech 2015.03.22, 04:00 PM
Replies: 8
Views: 1,261
Posted By LED
I've run X-speed for years with the stockdiff at...

I've run X-speed for years with the stockdiff at 7 and 8 pinion gears.
So a ratio of 6 to 5.25 should not be problem. On tracks with long straights we also used a 9 (ratio 4.6) pinion, but thats...
Forum: ZRound 2015.03.19, 01:09 PM
Replies: 3
Views: 876
Posted By LED
You simply make a different championship for each...

You simply make a different championship for each class you want to race. You can open multiple championships at the same time in the manager.
Forum: Motor Tech 2015.03.18, 10:25 AM
Replies: 44
Views: 3,616
Posted By LED
Question, why are the caps on the motor and not...

Question, why are the caps on the motor and not on the board? Do they need to be a close as possible to the source of the noise?
Forum: ZRound 2015.03.17, 10:49 AM
Replies: 13
Views: 1,640
Posted By LED
There are 26 bugs in it? :D

There are 26 bugs in it? :D
Forum: Mini-Z Science 2015.02.25, 12:17 PM
Replies: 30
Views: 9,990
Posted By LED
Yes I do, put them in and see if the motor runs...

Yes I do, put them in and see if the motor runs :-)
And I also agree with imxlr8ed. You provided some very useful info over the last months, and I also follow each one of your threads. That is why I...
Forum: Mini-Z Science 2015.02.25, 10:35 AM
Replies: 30
Views: 9,990
Posted By LED
I'm sorry but this must be the DUMBEST commentary...

I'm sorry but this must be the DUMBEST commentary I have ever read.
First off, nobody except the real electronics geeks have an adjustable power supply.
Secondly, suggesting to make a deliberate...
Forum: Mini-Z Science 2015.02.08, 11:27 AM
Replies: 16
Views: 1,603
Posted By LED
Basicly, one FET does not provide enough current...

Basicly, one FET does not provide enough current to drive the motor. That's why they put in 4.
Look at as it were tunnels. You can only pass a certain amount of cars through a tunnel in lets say one...
Showing results 1 to 25 of 500

 
Forum Jump

All times are GMT -5. The time now is 02:39 PM.


Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2011 Mini-ZRacer.com
Mini Inferno Sale - Up to $85 Instant Savings!
Micro-T Hop-Ups
RC18R, M18, Micro RS4, Mini-LST, TamTech-Gear, Minizilla, RC18T, RC18B, RC18MT
shop.tinyrc.com Products

more»
Tiny RC Community News
[03/22/17] MZR was on vacation, didn't... : All kidding aside, the host experienced a bit of a server meltdown last week and efforts to restore the site to a new server took longer than anticipated. The current server is temporary until - more»
[11/25/15] Did You Hear? Our Black... : Hey Racers,
We're getting started a bit early with our Black Friday sale this year.  Generally we're not supporters of retailers opening early on Thanksgiving, but in our case, we're - more»
[06/30/15] shop.tinyrc.com: Have You... : Hey All! Just a quick reminder to everyone that we post all of our shop.tinyrc.com Newletters here on the MZR Forum. If for some reason you miss them in your email inbox, you can always see the - more»
Mini-Z, Mini-Z Racer, MR-02, MA-010
M18, M18T, RC18T, Mini-LST, Mini-T, Micro RS4, XRay, 1/18, 18th scale
XMODS, XMOD, Micro Flight, ZipZaps, ZipZaps SE, Bit Char-G, MicroSizers, TTTT, Plantraco Desktop Rover, SuperSlicks, Digi Q
Mini Inferno, Mini Inferno ST, half EIGHT, 1/16, 16th scale
Epoch, Indoor Racer, 1/43, 43rd scale
E-Savage, eSavage, eZilla, e-Zilla, HPI
Robots, Bots, Bipeds, Wheeled, Manoi, Roomba, NXT, Lego, Hacking
Crawling, Crawlers, Micro, RC, Losi Mini-Rock Crawler, Duratrax Cliff Climber
Kyosho Minium, Caliber 120, Minium Forums
Mini-Z Hop-Ups, Mini-Z Parts, Mini Inferno Hop-Ups, Mini Inferno Parts, M18 Hop-Ups, M18 Parts