Mini-Z, Kyosho Mini-Z Racer, MR-03, MR-02, MA-010, Forums, News, Pictures, Parts, and Shop - Mini-ZRacer.com
Forums, Mini-Z, MiniZ, Kyosho Mini-Z, Kyosho MiniZ, Kyosho Mini-Z Racer
Mini-Z Hop-Ups, Mini-Z Parts, MiniZ Hop-Ups, MiniZ Parts, Kyosho Mini-Z Hop-Ups, Kyosho Mini-Z Parts, Kyosho MiniZ Hop-Ups, Kyosho MiniZ Parts, Kyosho Mini-Z Racer Hop-Ups, Racer Kyosho Mini-Z Parts
Old 2015.02.02, 06:38 AM   #1
ilove599xx
Registered User
 
Join Date: Jan 2015
Location: Taiwan
Posts: 106
FRONT STEERING KNUCKLE question

Dear all,

I have a question about the FRONT STEERING KNUCKLE.

I found out one of my original Kyosho FRONT STEERING KNUCKLE's bar can't be screwed up 100% with the wheel. The wheel can be moved from left to right tiny bit.

so I bought the new ALUMINUM FRONT STEERING KNUCKLE from 3racing and played for 2 hours. Today I found out one side can't be screwed up tight again.

Is that normal that FRONT STEERING KNUCKLE broke so easily?
ilove599xx is offline   Reply With Quote
Old 2015.02.02, 07:29 AM   #2
imxlr8ed
Registered User
 
imxlr8ed's Avatar
 
Join Date: Sep 2004
Location: Reading Pa.
Posts: 4,121
There should always be some slack on the front axles, if you're screwing wheels down tight, you're only creating a bind issue. If the the steel axle is spinning in the aluminum carrier... you must've been really cranking on those wheelnuts!
__________________
My Online Design Studio and Shop!

http://www.shapeways.com/shops/UID

http://www.howfastareyou.com

SUPPORT LBR!!!
(Local Basement Racing)
imxlr8ed is offline   Reply With Quote
Old 2015.02.02, 08:16 AM   #3
ilove599xx
Registered User
 
Join Date: Jan 2015
Location: Taiwan
Posts: 106
my wheelnuts just can't go through aluminum carrier's screw thread 100%. Is that normal?
ilove599xx is offline   Reply With Quote
Old 2015.02.02, 08:44 AM   #4
mleemor60
Curmudgeon & Moderator
 
mleemor60's Avatar
 
Join Date: Jan 2008
Location: Kannapolis, NC
Posts: 2,416
I have had 03's since their release date and have yet to break a plastic steering knuckle. However, I have seen several on the "sports" series fail within minutes of hitting the track for the first time. Possibility of a lesser grade of styrene being used in production since it has been moved to China? Highly likely. Intentional? Probably not. Kyosho's standards are pretty high.

Short knuckles are quite normal with the cheaper "off brand" components that are out there. Sometimes you get lucky with the less expensive brands but that is the exception and not the rule. We have all gone through it. To reasonably insure quality stick to the products from Kyosho(R246), Atomic, PN or X-Power and the suppliers that sells them.

When installing the plastic wheel nut study it carefully to insure that the stepped side goes toward the bearing or bushing. This is to minimize the contact area between the two pieces. Personally I would avoid the use of aluminum lock nuts for wheel retention. They tend to be pricey for what they are which creates a tendency to use them well beyond their service life while the first time a plastic nut doesn't draw up properly it goes in the circular file where it belongs. When purchasing the plastic units from PN though use caution as there have been quite a few bags(at our local HS) that have been too large and will not secure at all. I am not saying they are all bad but there have been some issues. I continue to use them since at their price point I just toss the defective ones as I run across them.
mleemor60 is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Fet and steering question nocomply Mini-Z AWD MA-010, MA-015 1 2009.01.10 11:11 AM
Alloy front steering spinndles for the F-1 Maximo Mini-Z F1 MF-010, MF-015 10 2004.11.07 02:24 AM
Steering Knuckle broke already? Eternalight Parts and Hop-ups 6 2004.06.12 12:36 AM
GPM Lock Nut + GPM Nylon Front Knuckle = no go? t00l Parts and Hop-ups 0 2003.09.13 11:02 AM
Steering Knuckle Play... F=ma Setups 1 2001.11.28 01:10 PM


All times are GMT -5. The time now is 06:44 AM.


Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Copyright 2011 Mini-ZRacer.com
Mini Inferno Sale - Up to $85 Instant Savings!
Micro-T Hop-Ups
RC18R, M18, Micro RS4, Mini-LST, TamTech-Gear, Minizilla, RC18T, RC18B, RC18MT
shop.tinyrc.com Products

more»
Tiny RC Community News
[03/22/17] MZR was on vacation, didn't... : All kidding aside, the host experienced a bit of a server meltdown last week and efforts to restore the site to a new server took longer than anticipated. The current server is temporary until - more»
[11/25/15] Did You Hear? Our Black... : Hey Racers,
We're getting started a bit early with our Black Friday sale this year.  Generally we're not supporters of retailers opening early on Thanksgiving, but in our case, we're - more»
[06/30/15] shop.tinyrc.com: Have You... : Hey All! Just a quick reminder to everyone that we post all of our shop.tinyrc.com Newletters here on the MZR Forum. If for some reason you miss them in your email inbox, you can always see the - more»
Mini-Z, Mini-Z Racer, MR-02, MA-010
M18, M18T, RC18T, Mini-LST, Mini-T, Micro RS4, XRay, 1/18, 18th scale
XMODS, XMOD, Micro Flight, ZipZaps, ZipZaps SE, Bit Char-G, MicroSizers, TTTT, Plantraco Desktop Rover, SuperSlicks, Digi Q
Mini Inferno, Mini Inferno ST, half EIGHT, 1/16, 16th scale
Epoch, Indoor Racer, 1/43, 43rd scale
E-Savage, eSavage, eZilla, e-Zilla, HPI
Robots, Bots, Bipeds, Wheeled, Manoi, Roomba, NXT, Lego, Hacking
Crawling, Crawlers, Micro, RC, Losi Mini-Rock Crawler, Duratrax Cliff Climber
Kyosho Minium, Caliber 120, Minium Forums
Mini-Z Hop-Ups, Mini-Z Parts, Mini Inferno Hop-Ups, Mini Inferno Parts, M18 Hop-Ups, M18 Parts