Mini-Z, Kyosho Mini-Z Racer, MR-03, MR-02, MA-010, Forums, News, Pictures, Parts, and Shop - Mini-ZRacer.com
Forums, Mini-Z, MiniZ, Kyosho Mini-Z, Kyosho MiniZ, Kyosho Mini-Z Racer
Mini-Z Hop-Ups, Mini-Z Parts, MiniZ Hop-Ups, MiniZ Parts, Kyosho Mini-Z Hop-Ups, Kyosho Mini-Z Parts, Kyosho MiniZ Hop-Ups, Kyosho MiniZ Parts, Kyosho Mini-Z Racer Hop-Ups, Racer Kyosho Mini-Z Parts
Old 2017.06.01, 05:28 AM   #1
herman
Registered User
 
Join Date: Nov 2001
Location: makati, philippines
Posts: 8,448
ko propo multi setting adapter instructions

just got a hold of one... and after searching... found the instructions...

click here

above are instructions for the mr02 module and dnano...
anybody know what the factory settings are for the mr03?


①Data Memory Number
The memory data specified is loaded and saved to the setting card. Eight memory data (1~8) can be retained.

②Load Memory / Save Memory
Press and hold the minus key to load (LD-) the saved data. Press and hold the plus key to save (SAV+) the data. Hold the key until OK is displayed.

③Receive Data / Transmit Data
Press and hold the minus key to receive (RX-) data to the devise. You must save the data to keep it in the setting card. Press and hold the plus key to transmit (TX+) the data on devise to the Mini-Z. Hold the key until OK is displayed.

④Gain (# GAIN)
Holding property of the steering servo is changed. Using the +/- keys, you can adjust the 3 strengths (Min, Mid, Strong). This changes the strength that the servo will keep its position.

⑤Speed (#SPEED)
Change the operational speed of the steering servo. Using the +/- keys, you can adjust the 5 speeds (Slow, 2, 3, 4, Fast).

⑥Punch (#PUNCH)
Change the rate of reaction of the initial movement of the steering servo. Using the +/- keys, you can adjust the punch with 10 different settings from 1 (Low) to 10 (High). When the setting is low, the movement is similar to an analog servo. Adjust to gain the proper control for your settings.

⑦Deadband (#D.BAND)
Configure the width of the neutral zone of the steering servo. Using the +/- keys, you can adjust the 3 widths (Narrow and Wide).

⑧Dampening (#DUMP)
Change the property of the steering servo when it comes back to neutral. Using the +/- keys, you can set it to Smooth or Over. Smooth setting rolls the servo back to neutral and the Over setting applies a brake before returning to neutral, but the movement remains unchanged.

⑨Motor Drive Frequency (#DRVFREQ)
Motor drive frequency of the throttle is changed. Using the +/- keys, you can adjust the 3 drive frequency settings. Mini-Z settings are 1.2/2.5/5.0KHz and d-nano settings are 1.1/2.3/4.8KHz. A low frequency increase torque but decreases runtime and a high frequency gives more runtime.

⑩Neutral Width (#NUTWIDE)
The width of the neutral zone of the throttle trigger can be adjusted. Using the +/- keys, you can configure 3 different widths Narrow, Mid and Wide.

⑪Inertia (#INERTIA)
Adjust the forward movement once the throttle is released. The 5 settings are Strong, 2, 3, 4 and OFF. A setting of Strong slows the carís roll the quickest and OFF allows the car to roll.

⑫Steering Gyro Gain (#ST.GAIN)
The effectiveness of the steering gyro for the d-nano is adjusted. Using the +/- keys, you can adjust the 5 phases OFF, 2, 3, 4 and Strong. The Strong setting will produce the most steering correction by the gyro. Cannot be used with Mini-Z.

⑬Throttle Gyro Gain (#TH.GAIN)
The effectiveness of the throttle gyro for the d-nano is adjusted. Using the +/- keys, you can adjust the 5 phases OFF, 2, 3, 4 and Strong. The Strong setting will produce the most thorttle correction by the gyro. Cannot be used with Mini-Z.


i turned the multi setting adjuster with the mr03 setting card on... and compared to the instructions i noticed that it looked like it had an additional setting... in between inertia and st.gain.... baktime - just guessing time to go into reverse? and it had the following settings....

Data mem#1
ld- sav+
rx- tx+
gain mid
speed fast
punch 2
d. band mid
dump over
drvfreq low
nutwide mid
inertia off
baktime 2
st gain 90
th gain 60

so are these the standard factory settings? you can save up to 8 different settings and "load" them into your car... pretty neat... what settings do you use?

thanks for any reply...
herman is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
FS - KO PROPO 2.4GHz Mini-Z Module w/ adapter davskee Mini-Z Marketplace 1 2010.09.08 08:32 PM
WTB: ICS Multi Setting Adapter & Setting Card Hekyl Mini-Z Marketplace 0 2009.05.14 07:57 PM
ICS Multi Setting Adapter & Mini-Z 2.4GHz Setting Card Set from Ko Propo Cherub1m New Products 5 2009.03.29 08:11 PM
KO Propo AD Band Roger Setups 153 2007.12.29 04:50 PM
FS: AD band setting adapter pchan0 Mini-Z Marketplace 7 2007.06.05 01:13 PM


All times are GMT -5. The time now is 04:39 PM.


Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Copyright ©2011 Mini-ZRacer.com
Mini Inferno Sale - Up to $85 Instant Savings!
Micro-T Hop-Ups
RC18R, M18, Micro RS4, Mini-LST, TamTech-Gear, Minizilla, RC18T, RC18B, RC18MT
shop.tinyrc.com Products

more»
Tiny RC Community News
[03/22/17] MZR was on vacation, didn't... : All kidding aside, the host experienced a bit of a server meltdown last week and efforts to restore the site to a new server took longer than anticipated. The current server is temporary until - more»
[11/25/15] Did You Hear? Our Black... : Hey Racers,
We're getting started a bit early with our Black Friday sale this year.  Generally we're not supporters of retailers opening early on Thanksgiving, but in our case, we're - more»
[06/30/15] shop.tinyrc.com: Have You... : Hey All! Just a quick reminder to everyone that we post all of our shop.tinyrc.com Newletters here on the MZR Forum. If for some reason you miss them in your email inbox, you can always see the - more»
Mini-Z, Mini-Z Racer, MR-02, MA-010
M18, M18T, RC18T, Mini-LST, Mini-T, Micro RS4, XRay, 1/18, 18th scale
XMODS, XMOD, Micro Flight, ZipZaps, ZipZaps SE, Bit Char-G, MicroSizers, TTTT, Plantraco Desktop Rover, SuperSlicks, Digi Q
Mini Inferno, Mini Inferno ST, half EIGHT, 1/16, 16th scale
Epoch, Indoor Racer, 1/43, 43rd scale
E-Savage, eSavage, eZilla, e-Zilla, HPI
Robots, Bots, Bipeds, Wheeled, Manoi, Roomba, NXT, Lego, Hacking
Crawling, Crawlers, Micro, RC, Losi Mini-Rock Crawler, Duratrax Cliff Climber
Kyosho Minium, Caliber 120, Minium Forums
Mini-Z Hop-Ups, Mini-Z Parts, Mini Inferno Hop-Ups, Mini Inferno Parts, M18 Hop-Ups, M18 Parts