2005.10.29, 04:58 PM
|
#31
|
Moderator
Join Date: Dec 2003
Location: Stafford, Va
Posts: 6,064
|
Quote:
Originally Posted by imxlr8ed
Great vid... It's a great instructional ! About time someone did it !
But... (there's always a but) As an admiring, fellow board surgeon... I must say your technique is rather brutal. Now don't get me wrong, I'm not trying to knock you here... I'm just amazed about a few things. I will describe...
I only use a 25 watt iron with a very long, narrow tip... I heard high heat for extended periods of time decreased the efficiency of the fet... or was I instructed wrongly ? I remove fets one foot at a time, I apply the iron to the foot, and use a dental hook to lever it upwards slowly. (you sat temato, I say tahmahto )
|
I usually tell if I've over heated the board when I can feel it through my fingers. I don't usually keep it on there long when I'm installing the chips.
Quote:
Originally Posted by imxlr8ed
Where did you get that iron tip... nasty ! I would say it's near impossible to install a triple stack with that, I'm sure you've done stacks... but I would bet it wasn't with that thang ! (if it was... you have jedi like control)
|
I didn't prep the iron in the beginning of the video. I noted that in the middle of the vid. Normally I would make it much sharper. When it's sharper it makes it easier to get to the legs by the box.
Quote:
Originally Posted by imxlr8ed
Why so much solder ?... I've never had to add solder to a single layer install, (stacks are a different story) I've always just used what was left on the pads after they've been smoothed, never had a problem !
|
I like to make sure there is plenty there for a real good connection. When running hot motors thos legs and solder get very hot. I believe that the more solder you have the less resistance and the best connection possible. Also it's pretty much ready to add more chips. The reverse chip was a used chips so the legs weren't factory bent.
Quote:
Originally Posted by imxlr8ed
Also, you can have a wad of solder on the "output" side of the fets, I've done stacks with "inline" connections, and some have the custom wad'o'solder down the back. (usually when I'm feeling lazy ) But you are absolutely right about the "input" side of the fet, I usually just pick gently between those with an exacto tip just to make sure there are no cross connections hiding in there.
|
I know you can and the first time I did a FET upgrade/repair there wasn't a video on the net and I could barely find pictures. Everything I found showed it that way but I never kept them for reference. I figure you can't go wrong if you reinstall them the way they were when you started.
Quote:
Originally Posted by imxlr8ed
Just a different style I guess ! (you big iron tip wielding savage you !!! ) Great job ! Wish I was more internet savvy so I could post a vid as well. Hey... maybe if you come across the pond again, we can have fet install races !
Cya !
|
I did the video instead of going to bed . I frequent the forums and alot of people were asking questions about FET upgrades. Everyone likes vids and I love making them so I thought I'd share my DIY upgrade.
I'd like to make another one. This time doing the removale/replacement/stack. It had been a while since I did an upgrade. I do all of my own work and most of the cars had already been done so I let my iron go to shat.
My goal with this video was to give people confidence and instruction to do it themselves.
-Byebye
|
|
|
2005.10.31, 06:58 AM
|
#32
|
Moderator
Join Date: Dec 2003
Location: Stafford, Va
Posts: 6,064
|
Quote:
Originally Posted by will3kgt
IT WORKED!.....Well, sort of. I did 2 x 3 fet stack this morning and when I did the motor test it didn't move then all of the sudden the motor came to life. So I turned off my car tried it again and the same thing happened....Oh yeah and my reverse doesn't work I'm going to try to resodder the fets again tommorow morning. Nevertheless, your video is the most helpful information I've recieved in my last 3 years of racing. Pictures will be forthcoming. Thanks again.
|
Let us know how it turned out.
-Byebye
|
|
|
2005.10.31, 10:05 AM
|
#33
|
Registered User
Join Date: Sep 2004
Location: Reading Pa.
Posts: 4,124
|
Quote:
Originally Posted by byebye
My goal with this video was to give people confidence and instruction to do it themselves.-Byebye
|
Well done, agree on all points ! We don't run too many hot motors here though, probably why I've never needed the extra solder. I have had feet come up before too, just a tap with the iron, and they're back to life. More than one way to skin a cat ! But when I saw the removal vid, and I saw that skanky soldering tip, humping the hell out of those fets, I was amazed ! (never even knew it was possible to do that !, though it would kill a board) I'd say your goal was more than acheived !
I wish this vid was out when I first started frying boards too ! (oh... so many fried, so long ago ! )
Thanks ByeBye !
|
|
|
2005.10.31, 10:27 AM
|
#34
|
Mechanic
Join Date: Jul 2004
Location: Chatsworth, GA
Posts: 3,577
|
you think his soldering tip was bad? LMAO my first FET job was a 2x4 stack on an 01, somehow I accomplished success with a wood burning kit figure that one out
__________________
Real Racers Do It Sideways.
PETA=People Eating Tastey Animals
those two chicks over there, not so hot. Dont get me wrong, I would still go for it, cause thats the type of equal opportunity guy I am.
I am a FIRM believer in "Run what ya brung"......Unless it's your MOUTH!!!
|
|
|
2005.10.31, 02:01 PM
|
#35
|
Registered User
Join Date: Sep 2004
Location: Reading Pa.
Posts: 4,124
|
Quote:
Originally Posted by Ninja
you think his soldering tip was bad? LMAO my first FET job was a 2x4 stack on an 01, somehow I accomplished success with a wood burning kit figure that one out
|
I got my current iron from, ughhh, I hate to say it... Walmart. It's a yellow plastic handle, 25 watt... came with this really narrow (1/8"dia), 1" long tip. Perfect for stack installs. Wood burner ?!?!... what next... MIGwelding ?!?!
|
|
|
2005.10.31, 06:52 PM
|
#36
|
Master of Thrash
Join Date: Oct 2002
Location: Arkansas
Posts: 4,980
|
Quote:
Originally Posted by Ninja
somehow I accomplished success with a wood burning kit figure that one out
|
My soldering iron is almost like a woodburning kit tool, that is about how cheaply it is made. It works just fine for PCB work. I have said before that using a higher wattage iron like say a 60w is very much like doing heart surgery with a chain saw.
|
|
|
2005.11.01, 09:59 AM
|
#37
|
Moderator
Join Date: Dec 2003
Location: Stafford, Va
Posts: 6,064
|
Quote:
Originally Posted by imxlr8ed
........ But when I saw the removal vid, and I saw that skanky soldering tip, humping the hell out of those fets, I was amazed ! .......
I wish this vid was out when I first started frying boards too ! (oh... so many fried, so long ago ! )
Thanks ByeBye !
|
Yeah I realized it when I started to on the next FET. That's when I went and filed the tip down. It's not good to do that to a new tip, I think because it comes with some kind of coating already. You really have to 'tin' the tip well and the solder will heatup on the board quickly. I did find a new iron from RS that's switchable from 15w 0r 30w. It should work well for these applications.
I too wish there was a more thorough vid out. I'm sure most of us have seen the one that was out showing the removal and install. Mine was driven by the fact that mini-zracer.com needed one of our own we could refer to.
Quote:
Originally Posted by HammerZ
My soldering iron is almost like a woodburning kit tool, that is about how cheaply it is made. It works just fine for PCB work. I have said before that using a higher wattage iron like say a 60w is very much like doing heart surgery with a chain saw.
|
LMAO!
I see that everyone improvises and that's what DIY is. Its just using what you can get your hands on and making it work. Back when I was really having a need for speed I was modding all my boards and removing FETs for different motors and setups. My tips were charp as needles and the iron I started out with just died before I left for London. I just threw away a tip that I sanded down to almost 1/4" long. I've scared up that little black box a dozen times but every install still works like a charm.
-Byebye
|
|
|
2005.11.01, 10:22 AM
|
#38
|
2-Z or not 2-Z...
Join Date: Nov 2001
Location: The Open Road
Posts: 2,678
|
Quote:
Originally Posted by byebye
...I've scared up that little black box a dozen times but every install still works like a charm.
|
I've removed that black box to stack FETs. It seemed easier to me, especially on the mr-02.
|
|
|
2005.11.01, 03:21 PM
|
#39
|
Moderator
Join Date: Dec 2003
Location: Stafford, Va
Posts: 6,064
|
I tried it and was happy with the fact that I had nothing to run into. It was sorta of a pain to get the box removed though. It does really help though.
-Byebye
|
|
|
2005.11.01, 04:36 PM
|
#40
|
Registered User
Join Date: Sep 2004
Location: Reading Pa.
Posts: 4,124
|
Quote:
Originally Posted by byebye
I tried it and was happy with the fact that I had nothing to run into. It was sorta of a pain to get the box removed though. It does really help though.
-Byebye
|
Always wondered... never asked... what is "the box" ? Actually... anyone have a full diagram of the board, and what the individual electronics do ? Or is that proprietary stuff ?
|
|
|
2005.11.01, 11:30 PM
|
#41
|
Master of Thrash
Join Date: Oct 2002
Location: Arkansas
Posts: 4,980
|
My guess is it is some sort of RF filter to guard the recever from the noise from the fets. I could be wrong though, I did say guess.
|
|
|
2005.11.02, 02:52 AM
|
#42
|
Moderator
Join Date: Dec 2003
Location: Stafford, Va
Posts: 6,064
|
I know there's some board schematic floating around here. On the iwaver board it's on the opposite side of the FETs so stacking is very easy. I don't think you can relocate them. I picked up some copper braid for cleaning solder mess. Never had much luck with them but I figure I would learn.
-Byebye
|
|
|
2005.12.08, 01:43 AM
|
#43
|
Registered User
Join Date: Jan 2005
Location: Nor-Cal
Posts: 987
|
byebye: Very kewl vids
|
|
|
2005.12.08, 08:44 AM
|
#44
|
Moderator
Join Date: Dec 2003
Location: Stafford, Va
Posts: 6,064
|
Quote:
Originally Posted by Roger
byebye: Very kewl vids
|
thanks!. I haven't gotten around to making a better video using the proper preperation but I'm sure it's helped some people.
You gonna FET stack the awd? Mine are at home right now(I'm in Germany) and I'm wondering how long they will last before I have to get the stuff to make them work?
-Byebye
|
|
|
2005.12.08, 10:08 AM
|
#45
|
Rockin Da Z
Join Date: Aug 2004
Location: NL, Canada
Posts: 3,112
|
excellent conclusion to the fet videos... That was a very nice and clean job... steady hands.
Has anyone tried a small piece of double sided tape on the bottom of the Fets so you don't have to hold them with the tweezers... also, does anyone use the "Cold Heat" iron ... burning up my board has always been a concern to me.
__________________
-------------------------------------------------------------------------------------------------------------------------------
||| There comes a time in every hobbist's life when they are forced to remorgage their house. |||
-------------------------------------------------------------------------------------------------------------------------------
|
|
|
Thread Tools |
|
Display Modes |
Rate This Thread |
Linear Mode
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -5. The time now is 06:20 AM.
|
|