Mini-Z, Kyosho Mini-Z Racer, MR-03, MR-02, MA-010, Forums, News, Pictures, Parts, and Shop - Mini-ZRacer.com
Forums, Mini-Z, MiniZ, Kyosho Mini-Z, Kyosho MiniZ, Kyosho Mini-Z Racer
Mini-Z Hop-Ups, Mini-Z Parts, MiniZ Hop-Ups, MiniZ Parts, Kyosho Mini-Z Hop-Ups, Kyosho Mini-Z Parts, Kyosho MiniZ Hop-Ups, Kyosho MiniZ Parts, Kyosho Mini-Z Racer Hop-Ups, Racer Kyosho Mini-Z Parts
Old 2003.02.16, 11:27 PM   #1
mlepage
Mini-Z Pro
 
Join Date: Nov 2002
Posts: 75
Powering the Body

I just mounted LED lights (front and rear) on my Overland, and let me say that it is a pain to connect them to the batteries whenever I mount the body. The body is hard enough to mount as it is without worrying about wires and connections!

Obviously, I have to do something about this soon. I was thinking about plug connectors, so I make a plug connection before mounting the body, and disconnect afterwards. But even that seems clumsy.

I believe someone made a contact connector for a Mini-Z. When you put the body on, it pressed down on two terminals he installed on top of the chassis. But that's too dependent on the body being mounted.

The ideal connection would be completely transparent. You mount the body, and voila you have power, no special connections needed.

Think about this for a second. What connection is guaranteed to always be the same for all Mini-Zs? For all bodies?

The mounting clips.

Look at them, they are just a millimeter away from the battery terminals. If only they touched! If only they could conduct!

So here's my idea.

I'm thinking of taking a bit of copper and putting it over the chassis part of the mounting system, so it touches the battery and makes a positive terminal on one side and a negative terminal on the other.

Then, I would put copper over the body part of the mounting system, so it makes contact with the terminals when mounted.

On the body, these terminals attach to wires which go to a switch, so you can turn power on/off independently of power to the chassis. Then, the body is powered. With a flick of the switch you have access to 6V, for LEDs or whatever.

Sure, you'd have to modify each body for power. But if your're mounting LEDs and whatnot, you're already modifying the body. You only have to modify the chassis once, then any body you've modified to have power just does, with no effort.

Unmodified bodies are not affected by the chassis mod.

Now, does this sound like an idea or what?
mlepage is offline   Reply With Quote
Old 2003.02.17, 12:50 AM   #2
Tango
Like this?!
 
Tango's Avatar
 
Join Date: Sep 2002
Location: HK
Posts: 204
Send a message via ICQ to Tango
I used External power source for lights.
__________________
Tango
HK Mini RC
Tango is offline   Reply With Quote
Old 2003.02.17, 01:26 AM   #3
pianoman
www.mini-zracer.com/shop/
 
pianoman's Avatar
 
Join Date: Dec 2002
Location: North Branch, Minnesota
Posts: 1,031
Thats a good idea. You could use some sort of foil to 'paint' the posts and mounting slots, right? That would work on all cars I suppose...
__________________
Pianoman has left the building!
pianoman is offline   Reply With Quote
Old 2003.02.17, 04:41 AM   #4
Ken Mifune
2-Z or not 2-Z...
 
Ken Mifune's Avatar
 
Join Date: Nov 2001
Location: The Open Road
Posts: 2,678
I saw pics of a similar set up. HK-dude had contacts on the front mount. Clean. Simple. and it was away from the antenna.
Ken Mifune is offline   Reply With Quote
Old 2003.02.17, 10:19 AM   #5
mlepage
Mini-Z Pro
 
Join Date: Nov 2002
Posts: 75
Photos?

If you find a link to these (or similar) photos, please post it here.

I know my LHS has thin copper sheets for modeling etc. I was thinking of getting one to make contacts from. Maybe later this week.
mlepage is offline   Reply With Quote
Old 2003.02.17, 10:21 AM   #6
mlepage
Mini-Z Pro
 
Join Date: Nov 2002
Posts: 75
Internal vs. External Power

Tango, of course if you use external power you have no need of this method.

But if you must use internal power, then I think this is the way to go.

I'm going to try modifying my Street Racer and Overland this way.
mlepage is offline   Reply With Quote
Old 2003.03.10, 05:38 PM   #7
mlepage
Mini-Z Pro
 
Join Date: Nov 2002
Posts: 75
Powering the Body Attempt

OK I finally had time to try my idea.

I got some thin brass strips, and some aluminum foil tape. Both conduct. I decided to try the foil tape.

I tested this on my Overland. So, I'm trying to get power from the main batteries, on the top front terminals (right behind the front wheels). It's a real pain to get access to, especially on the Pajero Overland.

I put photos here.

In the front photo, you can see the two chassis contacts above the front wheels, beside the front shocks. Next are two photos of the left side contact, then two photos of the right side contact. Finally, we have two photos of the body contacts; the rear photo is hard to see, but you can see it in the front photo.

I get good voltage across the chassis contacts. I tested a bit with one body contact and it lit my lights. However, when I mount the body, I find that I do not get power to the body. I suspect the contact is not adequate across the mount, although it seems fine and I press it and I get nothing.

I'll have more time to try it tomorrow. If it doesn't work, I may try the brass strip to make more solid terminals. Also, I may take power from the solder points where the battery case goes into the chassis (hard to explain, but look behind the front shocks).

So the approach has promise, but I need to tweak it a little to discover what works.
mlepage is offline   Reply With Quote
Old 2003.03.16, 08:10 PM   #8
mlepage
Mini-Z Pro
 
Join Date: Nov 2002
Posts: 75
Reimplementation Success

OK I reimplemented my idea as described, on my Overland.

I made small contacts out of brass. I glued some to the chassis, and soldered them to the main battery terminals.

Then I glued some to the body, off the mounts. These ones had a bit of flex, and an area for use as a terminal.

When the body is mounted, the contacts on the body touch the contacts on the chassis, thereby connecting the body terminals to the battery terminals.

Then, the body lightset is connected to the body terminals. There is nothing to do but mount the body. No extra cables or anything.

You can use unmodified bodies on a modified chassis, and you can use modified bodies on an unmodified chassis.

I'll post photos when I take a few.

If I could do it again, I'd be more careful. I used a butane soldering iron, which was too hot and melted the chassis a tiny bit (not much more than scratches from regular use, though). The glue doesn't like the heat, so likely I'd solder first then glue. I'd have taken more of the front of the Overland apart to get at the area I was installing the contacts. Other than that, it went well.

When I do my Street Racer, I'll be more careful.
mlepage is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
FOR SALE: Mini-Z Monster Truck, MR01, CP Cup Car & F1 Body biged358 Miscellaneous Discussion 21 2005.08.27 10:40 AM
Dogbreath Body Mounts How To DogbreathRacing Mini-Z Overland MV-01 6 2004.05.09 11:54 AM
What to do with your Mad Force body PAULANGELO Mini-Z Overland MV-01 5 2004.03.15 04:50 PM
Carbon Fiber Body Shells!! pukkita Parts and Hop-ups 4 2004.03.09 10:37 AM


All times are GMT -5. The time now is 04:11 AM.


Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2011 Mini-ZRacer.com
Mini Inferno Sale - Up to $85 Instant Savings!
Micro-T Hop-Ups
RC18R, M18, Micro RS4, Mini-LST, TamTech-Gear, Minizilla, RC18T, RC18B, RC18MT
shop.tinyrc.com Products

more»
Tiny RC Community News
[03/22/17] MZR was on vacation, didn't... : All kidding aside, the host experienced a bit of a server meltdown last week and efforts to restore the site to a new server took longer than anticipated. The current server is temporary until - more»
[11/25/15] Did You Hear? Our Black... : Hey Racers,
We're getting started a bit early with our Black Friday sale this year.  Generally we're not supporters of retailers opening early on Thanksgiving, but in our case, we're - more»
[06/30/15] shop.tinyrc.com: Have You... : Hey All! Just a quick reminder to everyone that we post all of our shop.tinyrc.com Newletters here on the MZR Forum. If for some reason you miss them in your email inbox, you can always see the - more»
Mini-Z, Mini-Z Racer, MR-02, MA-010
M18, M18T, RC18T, Mini-LST, Mini-T, Micro RS4, XRay, 1/18, 18th scale
XMODS, XMOD, Micro Flight, ZipZaps, ZipZaps SE, Bit Char-G, MicroSizers, TTTT, Plantraco Desktop Rover, SuperSlicks, Digi Q
Mini Inferno, Mini Inferno ST, half EIGHT, 1/16, 16th scale
Epoch, Indoor Racer, 1/43, 43rd scale
E-Savage, eSavage, eZilla, e-Zilla, HPI
Robots, Bots, Bipeds, Wheeled, Manoi, Roomba, NXT, Lego, Hacking
Crawling, Crawlers, Micro, RC, Losi Mini-Rock Crawler, Duratrax Cliff Climber
Kyosho Minium, Caliber 120, Minium Forums
Mini-Z Hop-Ups, Mini-Z Parts, Mini Inferno Hop-Ups, Mini Inferno Parts, M18 Hop-Ups, M18 Parts