Mini-Z, Kyosho Mini-Z Racer, MR-03, MR-02, MA-010, Forums, News, Pictures, Parts, and Shop - Mini-ZRacer.com
Forums, Mini-Z, MiniZ, Kyosho Mini-Z, Kyosho MiniZ, Kyosho Mini-Z Racer
Mini-Z Hop-Ups, Mini-Z Parts, MiniZ Hop-Ups, MiniZ Parts, Kyosho Mini-Z Hop-Ups, Kyosho Mini-Z Parts, Kyosho MiniZ Hop-Ups, Kyosho MiniZ Parts, Kyosho Mini-Z Racer Hop-Ups, Racer Kyosho Mini-Z Parts
Old 2016.06.09, 11:08 AM   #1
briankstan
Registered User
 
briankstan's Avatar
 
Join Date: Feb 2005
Location: West Jordan, Utah
Posts: 6,877
MR-03 Sports Blowing Fets

OK, so here is another question with regards to the sports chassis. There are about 10 new guys that picked up MR-03 Sports cars at the track that is racing mini-z. Of the 10+ guys running them at least 5 have blown fets on them when they put in the 70T motors.

I know that they weren't geared high as they were running only 6 or 7 tooth pinions with the stock diff or Kyosho ball diff.

Anyone else have issues running the 70T in the sports chassis? I know we had several people run them with no issues so I'm not sure what is going on over there at the track.

Maybe they aren't being careful when screwing in the motor terminals and that's the problem. Just looking for some info.

I'm keeping busy changing fet here lately, I haven't been this busy with fets since the AM cars were being run.
__________________
--Salt Lake Mini-Z---HFAY---MZR Gallery--
briankstan is offline   Reply With Quote
Old 2016.06.09, 11:20 AM   #2
arch2b
Moderator
 
arch2b's Avatar
 
Join Date: Sep 2002
Location: Washington, DC
Posts: 35,480
Send a message via AIM to arch2b
i can';t recall fets being an issue with the sports series at our track. it's mostly range or intermittent shut off. good thing fet replacement is cheap.
arch2b is offline   Reply With Quote
Old 2016.06.09, 01:16 PM   #3
mleemor60
Curmudgeon & Moderator
 
mleemor60's Avatar
 
Join Date: Jan 2008
Location: Kannapolis, NC
Posts: 2,549
With any of the PN 70T motors you have to be very careful that the motor wire "eyelets" don't come in contact with the little tiny gizmo hidden under the center tab of the top cover where the motor wires connect. Don't know what that thing is or does but it is not happy having a too close proximity with the negative wire. Be sure to trim the eyelets down to a smaller diameter or cut them off and solder the stock connectors onto the motor wires. Since that particular motor doesn't seem to be very happy with regular doses of "com" drops make sure the motor stays cleaned out and the throttle isn't held "on" while the car is nosed into a solid object. I have seen this issue even with an 80T motor.
mleemor60 is offline   Reply With Quote
Old 2016.06.09, 02:29 PM   #4
briankstan
Registered User
 
briankstan's Avatar
 
Join Date: Feb 2005
Location: West Jordan, Utah
Posts: 6,877
thanks Mike, Several of them are coming to race tonight and I'll discuss this with them. Hopefully we can cut down on their misfortune with blowing the boards.
__________________
--Salt Lake Mini-Z---HFAY---MZR Gallery--
briankstan is offline   Reply With Quote
Old 2016.06.10, 07:25 AM   #5
doug01n
Registered User
 
doug01n's Avatar
 
Join Date: Aug 2008
Location: São paulo, Brazil
Posts: 282
Send a message via MSN to doug01n
Keeping the throttle with stuck wheels may burn the fets. If they are experts on Mini-z, would not be an issue, but new guys don't know that the fet current goes very high when you keep the throttle trigger pushed after a crash and the car doesn't move.

No problems on our track too, but some drivers in Brazil had already burned some fets on the same way.
doug01n is offline   Reply With Quote
Old 2016.06.10, 07:43 AM   #6
briankstan
Registered User
 
briankstan's Avatar
 
Join Date: Feb 2005
Location: West Jordan, Utah
Posts: 6,877
Most of these guys are 10th scale off road racers, so you'd expect they would know with the throttle. It seemed most had the issues with their cars after changing motors or adding aftermarket parts so I tend to think that they were getting the battery terminals in contact with the little thing between the terminal mounts.
__________________
--Salt Lake Mini-Z---HFAY---MZR Gallery--
briankstan is offline   Reply With Quote
Old 2016.06.10, 08:11 AM   #7
mleemor60
Curmudgeon & Moderator
 
mleemor60's Avatar
 
Join Date: Jan 2008
Location: Kannapolis, NC
Posts: 2,549
If any driver comes from a background of racing where reverse isn't allowed then the first thing that comes to mind is to blip the throttle a couple of times to induce bounce back so they can drive off without being marshaled.

I do suspect though that the main issue is the motor wires coming in contact with something unfriendly.
mleemor60 is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Install Fets in MR-03s Sports alexander6996 Mini-Z Racer MR-03, MR-03 VE, Sports Series, EVO 6 2015.04.28 10:32 AM
blowing fets saddad Mini-Z Science 2 2013.07.28 08:49 PM
keep blowing fets on my 03 ???? kromie101 Miscellaneous Discussion 2 2010.06.20 07:17 PM
Vishay Si4501 fets 3x2, works great.. CrashTestJohnny Parts and Hop-ups 1 2007.01.29 06:28 AM
calling miketre... tips on installing 4562 herman Parts and Hop-ups 7 2003.09.26 03:46 AM


All times are GMT -5. The time now is 02:13 AM.


Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2011 Mini-ZRacer.com
Mini Inferno Sale - Up to $85 Instant Savings!
Micro-T Hop-Ups
RC18R, M18, Micro RS4, Mini-LST, TamTech-Gear, Minizilla, RC18T, RC18B, RC18MT
shop.tinyrc.com Products

more»
Tiny RC Community News
[03/22/17] MZR was on vacation, didn't... : All kidding aside, the host experienced a bit of a server meltdown last week and efforts to restore the site to a new server took longer than anticipated. The current server is temporary until - more»
[11/25/15] Did You Hear? Our Black... : Hey Racers,
We're getting started a bit early with our Black Friday sale this year.  Generally we're not supporters of retailers opening early on Thanksgiving, but in our case, we're - more»
[06/30/15] shop.tinyrc.com: Have You... : Hey All! Just a quick reminder to everyone that we post all of our shop.tinyrc.com Newletters here on the MZR Forum. If for some reason you miss them in your email inbox, you can always see the - more»
Mini-Z, Mini-Z Racer, MR-02, MA-010
M18, M18T, RC18T, Mini-LST, Mini-T, Micro RS4, XRay, 1/18, 18th scale
XMODS, XMOD, Micro Flight, ZipZaps, ZipZaps SE, Bit Char-G, MicroSizers, TTTT, Plantraco Desktop Rover, SuperSlicks, Digi Q
Mini Inferno, Mini Inferno ST, half EIGHT, 1/16, 16th scale
Epoch, Indoor Racer, 1/43, 43rd scale
E-Savage, eSavage, eZilla, e-Zilla, HPI
Robots, Bots, Bipeds, Wheeled, Manoi, Roomba, NXT, Lego, Hacking
Crawling, Crawlers, Micro, RC, Losi Mini-Rock Crawler, Duratrax Cliff Climber
Kyosho Minium, Caliber 120, Minium Forums
Mini-Z Hop-Ups, Mini-Z Parts, Mini Inferno Hop-Ups, Mini Inferno Parts, M18 Hop-Ups, M18 Parts