Mini-Z, Kyosho Mini-Z Racer, MR-03, MR-02, MA-010, Forums, News, Pictures, Parts, and Shop - Mini-ZRacer.com
Forums, Mini-Z, MiniZ, Kyosho Mini-Z, Kyosho MiniZ, Kyosho Mini-Z Racer
Mini-Z Hop-Ups, Mini-Z Parts, MiniZ Hop-Ups, MiniZ Parts, Kyosho Mini-Z Hop-Ups, Kyosho Mini-Z Parts, Kyosho MiniZ Hop-Ups, Kyosho MiniZ Parts, Kyosho Mini-Z Racer Hop-Ups, Racer Kyosho Mini-Z Parts
Old 2013.10.09, 04:36 PM   #1
Gonman
Registered User
 
Join Date: Oct 2013
Posts: 4
Mini-z steering problem [need help]

Hello people, this is my first post at this forum and unfortunately I am not here for good reasons

My mini-z mr-02 have been stopped for about 2 years. Two weeks ago I've decided to put it back in action but a problem with the steering is making me upset.

So, the problem is that whenever I turn on my mini-z and my controller, the steering starts glitching and it doesn't let me center it.

To help you understanding what I am talking about here is a video I made

http://www.youtube.com/watch?v=WDXjzaYGXYo

I have already replaced the pot with a new one, i've already tried to control it from another remote and with another crystal but it didn't work.

Well, I don't no what's happening. Do you guys have any idea of what could be the problem?
Gonman is offline   Reply With Quote
Old 2013.10.09, 04:45 PM   #2
mleemor60
Curmudgeon & Moderator
 
mleemor60's Avatar
 
Join Date: Jan 2008
Location: Kannapolis, NC
Posts: 2,500
Is antenna on transmitter fully extended? Is antenna on chassis securely fastened? Transmitter batteries new or in good condition? Tried to place transmitter and receiver farther apart? Screws that attach board to chassis secure? Transmitter crystal in transmitter and receiver crystal in car? Take everything back to basics. One at a time so when you locate the issue you will know what it is. Good luck and welcome to our insanity.
mleemor60 is offline   Reply With Quote
Old 2013.10.09, 07:06 PM   #3
r46
Registered User
 
r46's Avatar
 
Join Date: Jan 2012
Location: uk
Posts: 103
best result I found when ran am was with kyosho KT3 handset(tried kt5,acom,ae,futaba glitching galore ) an any electricial equipment close by causes interference greatly.
have a read here worked great for me but had to go 2.4 in end
http://mini-zracer.com/forums/showthread.php?t=31699
__________________
http://i810.photobucket com/albums/zz24/triks75/Wlmr-blue-sm jpg

Motoracer x2

02ex Hfay

02mod

03 Hfay

03 mod x2

03VE

F1ve

AMZ

TZ4
Dnano
#911 #Enzo # Lambo

reserved for
r46 is offline   Reply With Quote
Old 2013.10.10, 06:55 PM   #4
Gonman
Registered User
 
Join Date: Oct 2013
Posts: 4
Mates, I've already re-soldered every single wire into the board and in the potentiometer, I've changed the antenna, I've tried to control it from different distances and all I got was that annoying problem!

Here is a new video so you can see how annoying it is!
http://www.youtube.com/watch?v=Ko4m1-Fp3Io

I don't think I've much more things to try and I'm getting really upset because there is a new track in my town and I can't teach my slow friends how to drive

Do you guys have any suggestion? How much does a new electric board costs? Is it better to spend money on a new one or to invest in a MR03?
I am not in the mod to spend a lot of money, so fixing this problem would be really great!

What do you think about it?
Gonman is offline   Reply With Quote
Old 2013.10.11, 07:40 AM   #5
herman
Registered User
 
Join Date: Nov 2001
Location: makati, philippines
Posts: 8,603
hmm... the transmitter looks a bit different... does the same thing happen if you try going back to a kt-5 or kt-2? have you tried a different set of crystals?

in the second video it sounds like something is binding... did you try cleaning out the servo gears?

apart from that maybe you can try changing the servo motor?

wish i could be of more help...

you might find a cheap mr02 these days... at least you'll have spares when you buy it vs. purchasing a board only... good luck... and let us all know how it turns out...
herman is offline   Reply With Quote
Old 2013.10.11, 10:41 AM   #6
Gonman
Registered User
 
Join Date: Oct 2013
Posts: 4
By servo you mean this, right?



I've replaced it but nothing happens.

I've tried with some other crystals and with the original transmitter but nothing...

The sound you ear in the second video is the steering motor trying to run. If i take it out of the chassis it wont stop spining
Gonman is offline   Reply With Quote
Old 2013.10.11, 11:28 AM   #7
imxlr8ed
Registered User
 
imxlr8ed's Avatar
 
Join Date: Sep 2004
Location: Reading Pa.
Posts: 4,121
Set the radio to center, there is a little silver dial on top of the board you can use to center the servo to the radio.

I can't see the vids here at work but it sounds like a crystal issue to me.

If it's not that, then I'd make sure the antenna is away from any kind of carbon fiber.

If there's still an issue, I'd swap the potentiometer... might be a hairline crack in it.

The servo is going to spin until it makes the pot find center when it's all out of the car. I can usually slowly turn the potentiometer with my fingers until the motor stops.

Where are you from?... I'm curious as to what track is opening up.

Odd note here... crystals seem to have a shelf life. I can't explain that but in my AM history, some of my older crystals would just act up occasionally. Also, the old radios can get funky if they get bashed around a bit, I've got a whole box of sketchy AM radios in my shed collecting dust!
__________________
My Online Design Studio and Shop!

http://www.shapeways.com/shops/UID

http://www.howfastareyou.com

SUPPORT LBR!!!
(Local Basement Racing)

Last edited by imxlr8ed; 2013.10.11 at 11:31 AM.
imxlr8ed is offline   Reply With Quote
Old 2013.10.11, 11:47 PM   #8
I-Lap
Registered User
 
Join Date: Oct 2004
Location: NW Chicago Burbs
Posts: 103
Yeah, check or try another pot. The way it seems to go to extremes would indicate an open circuit between the outer terminals.

If the motor is connected, I didn't notice any activity there, so a crystal/rf/interference issue is not likely. If it was one of those, the motor would go nuts too.
__________________
I-Lap Timing Systems
Precision Timing for Small Scale Motorsports
www.rclapcounter.com
I-Lap is offline   Reply With Quote
Old 2013.10.14, 01:32 PM   #9
Gonman
Registered User
 
Join Date: Oct 2013
Posts: 4
Hey mates!

I've tried every little thing you all have suggested and I wasn't successful, so I end up buying an used but almost new MR-02

Now I'm waiting for the arrival of my new boy and ASAP I will be changing the upgrades from my old mini-z to the new one and see how it goes!

imxlr8ed, I'm from Aveiro, in Portugal! A bit far from you guys, i think
Gonman is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Steering problem jbenthobbies Mini-Z AWD MA-010, MA-015 7 2006.11.26 02:10 PM
major steering problem olly986 Setups 5 2006.09.03 07:39 PM
MM02 steering problem pyro147 Beginner Questions 6 2006.03.29 03:54 AM
I'm having a problem with my steering on the Iwaver monster joecombs Mini-Z Monster MM-01 1 2006.01.09 08:58 PM
Mini Z vs Colt Mini Justin Miscellaneous Discussion 71 2002.01.18 08:31 AM


All times are GMT -5. The time now is 06:12 AM.


Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Copyright 2011 Mini-ZRacer.com
Mini Inferno Sale - Up to $85 Instant Savings!
Micro-T Hop-Ups
RC18R, M18, Micro RS4, Mini-LST, TamTech-Gear, Minizilla, RC18T, RC18B, RC18MT
shop.tinyrc.com Products

more»
Tiny RC Community News
[03/22/17] MZR was on vacation, didn't... : All kidding aside, the host experienced a bit of a server meltdown last week and efforts to restore the site to a new server took longer than anticipated. The current server is temporary until - more»
[11/25/15] Did You Hear? Our Black... : Hey Racers,
We're getting started a bit early with our Black Friday sale this year.  Generally we're not supporters of retailers opening early on Thanksgiving, but in our case, we're - more»
[06/30/15] shop.tinyrc.com: Have You... : Hey All! Just a quick reminder to everyone that we post all of our shop.tinyrc.com Newletters here on the MZR Forum. If for some reason you miss them in your email inbox, you can always see the - more»
Mini-Z, Mini-Z Racer, MR-02, MA-010
M18, M18T, RC18T, Mini-LST, Mini-T, Micro RS4, XRay, 1/18, 18th scale
XMODS, XMOD, Micro Flight, ZipZaps, ZipZaps SE, Bit Char-G, MicroSizers, TTTT, Plantraco Desktop Rover, SuperSlicks, Digi Q
Mini Inferno, Mini Inferno ST, half EIGHT, 1/16, 16th scale
Epoch, Indoor Racer, 1/43, 43rd scale
E-Savage, eSavage, eZilla, e-Zilla, HPI
Robots, Bots, Bipeds, Wheeled, Manoi, Roomba, NXT, Lego, Hacking
Crawling, Crawlers, Micro, RC, Losi Mini-Rock Crawler, Duratrax Cliff Climber
Kyosho Minium, Caliber 120, Minium Forums
Mini-Z Hop-Ups, Mini-Z Parts, Mini Inferno Hop-Ups, Mini Inferno Parts, M18 Hop-Ups, M18 Parts