Mini-Z, Kyosho Mini-Z Racer, MR-03, MR-02, MA-010, Forums, News, Pictures, Parts, and Shop - Mini-ZRacer.com
Forums, Mini-Z, MiniZ, Kyosho Mini-Z, Kyosho MiniZ, Kyosho Mini-Z Racer
Mini-Z Hop-Ups, Mini-Z Parts, MiniZ Hop-Ups, MiniZ Parts, Kyosho Mini-Z Hop-Ups, Kyosho Mini-Z Parts, Kyosho MiniZ Hop-Ups, Kyosho MiniZ Parts, Kyosho Mini-Z Racer Hop-Ups, Racer Kyosho Mini-Z Parts
Old 2002.08.27, 02:48 AM   #1
TECHN0
Registered User
 
Join Date: Aug 2002
Location: Arcadia, CA
Posts: 37
Car spinning toward the right

Hi,

I'm confused as to why one of my car keeps spinning to the right when accelerating. I'm running xspeed with proline rear roll socks and squat ball bearings. New 40 tires by Kyosho.

No hop ups in the front yet and still waiting for my mail orders for some topcat stuff including the bulkhead, tie rods, knuckles, kingpins.

What would I need in terms of stabilizing the front end during acceleration so the car doesn't spins? it is because of way too much torque? I'd think it should leap forward instead right?

Techn0
btw, those squat ball bearings are SwwwwwwwwwweeeeeTTTT!
TECHN0 is offline  
Old 2002.08.27, 03:28 AM   #2
jeffrey
undisputed
 
jeffrey's Avatar
 
Join Date: Nov 2001
Location: Waipahu, Hawaii, USA
Posts: 1,099
Send a message via AIM to jeffrey
do you have a ball diff.?
__________________
FASTEST NON-TURBO RACER!

I DON'T NEED A FAST MOTOR TO GO FAST!
jeffrey is offline  
Old 2002.08.27, 03:58 AM   #3
TECHN0
Registered User
 
Join Date: Aug 2002
Location: Arcadia, CA
Posts: 37
Quote:
Originally posted by jeffrey
do you have a ball diff.?
Yes in fact I do. It's made by Proline I think and it's purple. I forgot to mention that on my post.

Techn0
TECHN0 is offline  
Old 2002.08.27, 04:48 AM   #4
butler
Mini-Z Chief
 
butler's Avatar
 
Join Date: Jan 2002
Location: UK, Hemel Hempstead
Posts: 691
Send a message via MSN to butler
Try tightening your diff up. Remember the rear weight distribution is a little uneven because of the motor location is off centre.
__________________
Haynes Manual: Prise away plastic locating pegs...
Reality: Snap off...

Haynes Manual: Lightly...
Reality: Start off lightly and build up till the veins on your forehead are throbbing then re-check the manual because this can not be 'lightly' what you are doing now.
butler is offline  
Old 2002.08.27, 05:05 AM   #5
le-manz
Mini-Zter
 
le-manz's Avatar
 
Join Date: Nov 2001
Location: Copenhagen-Denmark-Europe-The world-Space-Giants toenail
Posts: 403
Also take some time to get the steerring trim on the TX right, and it should be done everytime you turn it on. Well it's one of the flaws of the mini-z

try change the tires to 20, world of difference. if you still experience oversteer then change the fronts to 30 but only the fronts. Tires is by far the most important hop-up for your car so try out some different combinations to see what best for your driving style and surface
le-manz is offline  
Old 2002.08.27, 05:09 AM   #6
butler
Mini-Z Chief
 
butler's Avatar
 
Join Date: Jan 2002
Location: UK, Hemel Hempstead
Posts: 691
Send a message via MSN to butler
le-manz, its spins on acceleration. So I guess softer rears will help.
__________________
Haynes Manual: Prise away plastic locating pegs...
Reality: Snap off...

Haynes Manual: Lightly...
Reality: Start off lightly and build up till the veins on your forehead are throbbing then re-check the manual because this can not be 'lightly' what you are doing now.
butler is offline  
Old 2002.08.27, 05:14 AM   #7
le-manz
Mini-Zter
 
le-manz's Avatar
 
Join Date: Nov 2001
Location: Copenhagen-Denmark-Europe-The world-Space-Giants toenail
Posts: 403
lol thats what i meant, but its not coming across very well
what i meant is go for 20 around the car, front and back!!!!!
le-manz is offline  
Old 2002.08.27, 05:17 AM   #8
butler
Mini-Z Chief
 
butler's Avatar
 
Join Date: Jan 2002
Location: UK, Hemel Hempstead
Posts: 691
Send a message via MSN to butler
Its all good.
__________________
Haynes Manual: Prise away plastic locating pegs...
Reality: Snap off...

Haynes Manual: Lightly...
Reality: Start off lightly and build up till the veins on your forehead are throbbing then re-check the manual because this can not be 'lightly' what you are doing now.
butler is offline  
Old 2002.08.27, 03:39 PM   #9
TECHN0
Registered User
 
Join Date: Aug 2002
Location: Arcadia, CA
Posts: 37
Quote:
Originally posted by butler
Try tightening your diff up. Remember the rear weight distribution is a little uneven because of the motor location is off centre.
Thanks. Will try to tighten the read diff. Any way of doing this correctly?

Techn0
TECHN0 is offline  
Old 2002.08.27, 03:39 PM   #10
TECHN0
Registered User
 
Join Date: Aug 2002
Location: Arcadia, CA
Posts: 37
Quote:
Originally posted by le-manz
Also take some time to get the steerring trim on the TX right, and it should be done everytime you turn it on. Well it's one of the flaws of the mini-z

try change the tires to 20, world of difference. if you still experience oversteer then change the fronts to 30 but only the fronts. Tires is by far the most important hop-up for your car so try out some different combinations to see what best for your driving style and surface
Same thing with 20 tires. I think the read traction is too stiff, but then, it should go straight and not just spin to one side right?

Techn0
TECHN0 is offline  
Old 2002.08.27, 03:40 PM   #11
TECHN0
Registered User
 
Join Date: Aug 2002
Location: Arcadia, CA
Posts: 37
Quote:
Originally posted by butler
le-manz, its spins on acceleration. So I guess softer rears will help.
I think I'll try that route too and use a softer spring.. But it's weird.. LOL

Techn0
TECHN0 is offline  
Old 2002.08.27, 04:20 PM   #12
Russ
Super Moderator
 
Russ's Avatar
 
Join Date: Nov 2001
Location: Atlanta, GA
Posts: 1,448
Send a message via AIM to Russ
You need to adjust the tweak for your H plate. That is why the car is spinning one way. You said it spins to the right, so the back left tire is getting more traction than the back right. Unscrew the front spur-side screw 1/4 of a turn, then try it again. If you need more, unscrew it again until it is out 1/2 a turn. If you still need more, unscrew the back nonspur-side screw 1/4 a turn. What you are doing when you do this is transfer the weight from the rear left tire to the rear right tire so an equal amount of weight is distributed to both tires evenly. Nothing will cure the problem of a tweaked H plate other than adjusting the actual H plate itself. I've seen H plates so bad that just unscrewing the screws won't help. They even had to put washers under one side of the H plate.
__________________
Russ

--------------------------------------------

Last edited by Russ; 2002.08.27 at 04:23 PM.
Russ is offline  
Old 2002.08.27, 05:24 PM   #13
TECHN0
Registered User
 
Join Date: Aug 2002
Location: Arcadia, CA
Posts: 37
Quote:
Originally posted by Russ
You need to adjust the tweak for your H plate. That is why the car is spinning one way. You said it spins to the right, so the back left tire is getting more traction than the back right. Unscrew the front spur-side screw 1/4 of a turn, then try it again. If you need more, unscrew it again until it is out 1/2 a turn. If you still need more, unscrew the back nonspur-side screw 1/4 a turn. What you are doing when you do this is transfer the weight from the rear left tire to the rear right tire so an equal amount of weight is distributed to both tires evenly. Nothing will cure the problem of a tweaked H plate other than adjusting the actual H plate itself. I've seen H plates so bad that just unscrewing the screws won't help. They even had to put washers under one side of the H plate.
Thanks for your advice Russ,

Tweaked meaning bend out of shape somehow? So would changing another H plate cure this? or is it just the nature of these mini-z?

Techn0
TECHN0 is offline  
Old 2002.08.27, 07:41 PM   #14
Russ
Super Moderator
 
Russ's Avatar
 
Join Date: Nov 2001
Location: Atlanta, GA
Posts: 1,448
Send a message via AIM to Russ
Even though they may look it, 99% of the H plates made aren't 100% flat all around. Even if they are, the weight balance from the motor throws it off too. It is highly unlikely that you have the perfect setup right out of the box. So, yeah, your H bar is probably bent, or tweaked a little, you know, twisted a bit. You have to compensate for that little twist.
__________________
Russ

--------------------------------------------
Russ is offline  
 

Bookmarks

Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
throttle adjustment on the car? Zephyr von Bobo iWaver 9 2006.05.11 08:07 PM
i'd like to have a car i can race on the street, need info! builthatch Off-Topic 16 2006.02.12 01:18 PM
Getting out of Mini-Z racing.... PD2 Miscellaneous Discussion 10 2006.01.19 09:35 PM
A new Stock Car class will be starting this fall at CP Mini RC Raceway Blackno3 CP Mini RC Raceway, NY 58 2004.10.27 09:23 PM
Ideas for sharpening turning radius for 02's bbeattie Mini-Z Racer MR-02 10 2004.06.01 03:15 AM


All times are GMT -5. The time now is 08:45 AM.


Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2011 Mini-ZRacer.com
Mini Inferno Sale - Up to $85 Instant Savings!
Micro-T Hop-Ups
RC18R, M18, Micro RS4, Mini-LST, TamTech-Gear, Minizilla, RC18T, RC18B, RC18MT
shop.tinyrc.com Products

more»
Tiny RC Community News
[03/22/17] MZR was on vacation, didn't... : All kidding aside, the host experienced a bit of a server meltdown last week and efforts to restore the site to a new server took longer than anticipated. The current server is temporary until - more»
[11/25/15] Did You Hear? Our Black... : Hey Racers,
We're getting started a bit early with our Black Friday sale this year.  Generally we're not supporters of retailers opening early on Thanksgiving, but in our case, we're - more»
[06/30/15] shop.tinyrc.com: Have You... : Hey All! Just a quick reminder to everyone that we post all of our shop.tinyrc.com Newletters here on the MZR Forum. If for some reason you miss them in your email inbox, you can always see the - more»
Mini-Z, Mini-Z Racer, MR-02, MA-010
M18, M18T, RC18T, Mini-LST, Mini-T, Micro RS4, XRay, 1/18, 18th scale
XMODS, XMOD, Micro Flight, ZipZaps, ZipZaps SE, Bit Char-G, MicroSizers, TTTT, Plantraco Desktop Rover, SuperSlicks, Digi Q
Mini Inferno, Mini Inferno ST, half EIGHT, 1/16, 16th scale
Epoch, Indoor Racer, 1/43, 43rd scale
E-Savage, eSavage, eZilla, e-Zilla, HPI
Robots, Bots, Bipeds, Wheeled, Manoi, Roomba, NXT, Lego, Hacking
Crawling, Crawlers, Micro, RC, Losi Mini-Rock Crawler, Duratrax Cliff Climber
Kyosho Minium, Caliber 120, Minium Forums
Mini-Z Hop-Ups, Mini-Z Parts, Mini Inferno Hop-Ups, Mini Inferno Parts, M18 Hop-Ups, M18 Parts